We run a comp here at Albury High in Australia for our Yr 12 Engineering Studies students involving max. 50 popsicle sticks, PVA wood glue and 2m of extra strong thread. Structures have to span 400mm and are centrally loaded. Here’s a photo of our 2010 winner which weighed in at 69 grams and held 58kgs giving an efficiency using the formula on your website if i used it correctly of around 12000!
This bridge was built by Michael in Quebec.
I have a bridge I built for a physics for engineers class I’m taking in cegep (QUEBEC). My partner and I didn’t have much confidence in it, but it blew the competition away! The design was a fairly straightforward arch as you can see. We primarily focused on [...]
These are some pictures of a bridge I built mainly out of boredom, but also since I have an interest in engineering. It’s a large cantilever bridge, meaning it has two arms that extend beyond their piers that hold up a center suspended span. It’s 10′ 2″ long and as of right now is hanging across my bedroom ceiling
Nic’s design held a weight of 224kg and had a final efficiency of 1020. It did not shear or snap at any member, but bowed in the second third of member C-E. This member did have angled bracing to stop bowing and this brace did not snap it was only the glue joins in this brace that failed. The truss ballooned out at the point when 2.2kN of force was applied. It was at this point that the test was stopped
These are the photos of a popsicle bridge that I made for a bridge building contest at my university in Spain. The weight of the bridge was 3.9kg, and the bridge held 700kg without breaking. This gives it an efficiency score of 180. The dimensions of underneath the arc are 90cm x 45cm.
Build This Bridge
This popsicle stick bridge was made from 40, unmodified popsicle sticks. The bridge spanned 12 inches, was 4 inches tall and 3 inches wide. I used only Elmer’s white glue to build the bridge. It weighed 57.4 grams (0.13 pounds), and held 90 pounds. Its efficiency score was 712.
This was the [...]
This popsicle bridge was made from 58 unmodified popsicle sticks. It was 25 inches long, 4 inches tall, and 3 inches wide. I used only Elmer’s white glue to build the bridge. It weighed 86.5 grams, and held 45 pounds. Its efficiency score was 248.
Build This Bridge
I redesigned this bridge from the earlier version. [...]
Have you wanted to make a strong popsicle stick bridge that used 100 popsicle sticks or less? This popsicle bridge was made from 98 unmodified popsicle sticks and WeldBond glue. It was 21 inches long, 4 inches tall, and 4 inches wide. It weighed about 150 grams, and held 140 pounds. With less than 100 [...]
Hi, I just wanted to share the excitement…by using ideas from your website (recommended by my son’s Cub Scout leader) my son Jackson and I were able to build a Popsicle bridge with approximately 125 sticks. It set a new record by holding 500 lbs. for about 15 seconds before breaking! Thanks for the great ideas…not bad for the first try
This is a popsicle stick bridge I built while in the last few weeks of my fall college semester. I used 924 popsicle sticks to build this bridge. This bridge was 5 feet long, 10 inches tall, and 8 inches wide. I had to sort through 2600 popsicle sticks to find enough usable ones. The first testing of the bridge consisted of 220 pounds worth of weights. The second testing included putting a piece of plywood on top of the bridge and me standing on it (170 pounds). We noticed that one end diagonal chord was bending tremendously, so I decided to call off any more testing until I could repair that one piece
The American Society of Civil Engineers has been putting on an annual popsicle stick bridge competition for high schools in western Washington for the last 13 years. Last year, I entered with a 350 gram, 30 inch long bridge that carried 567 pounds under their hydraulic press. Their website is http://www.seattleasce.org/ymf/popsiclebridge.html . They score the bridges on efficiency (I won at that!) and aesthetics (I don’t know why I didn’t win at that)
